In the office, the inkjet printer is to use it in a more general one device. Inkjet printers due to the use, maintenance, improper operation and other factors will often be some failures, how to address the concerns of the user. In this work, we always put the common faults and treatment sum up, we want to help.
A common fault: printing ink scarce, illegible handwriting processing, most of the fault is due to the long-term unused printers or other reasons, resulting in the ink delivery system disorders or nozzle clogging.
Excluded: If sony vgp-bps13a/b battery nozzle clogging is not very powerful, direct the implementation of cleaning operations on the printer can be. If no effect after repeated washing, you can win the cartridge (one for non-printer cartridge nozzle, the nozzle need to win, but the need to carefully), put the nozzle in warm water soak for a while, note that the circuit boards must not some are soaked in water, or else, stained with absorbent paper to take away the water droplets, and then washed several nozzles installed on it.
Fault Two: Replace the new cartridge, the printer in the boot panel on the “ink to make” light treatment
Under normal circumstances, when the ink has run out of time “to make the ink” light will be lit. Replacement ink cartridges, the printer panel on the “ink to make” the light was bright, the occurrence of this failure, one may Cartridge is not fitted properly, the other may be won in the off state their own old cartridge, replace with new cartridges. As to replace the print cartridge, printer ink will charge the ink delivery system, and this process can not be turned off, so the Dell Inspiron 1545 battery printer can not detect the re-install the cartridges. In addition, some printer ink capacity of the measurement is the use of electronic counters inside the printer to the count (especially in the use of color ink on the statistics), when the counter reaches a certain value, to determine the printer ink exhausted. In the ink cartridge replacement process, the printer will carry out its internal reset the electronic counter, thus confirming the installation of a new cartridge.
Solution: Turn on the power, the print head moves to the cartridge replacement position. After installing the cartridge, so that charge printer ink, ink filling process is finished, troubleshooting.
Troubleshooting III: Treatment of head soft plug
Block refers to the soft plug for various reasons on the viscosity of the ink in the nozzle due to break bigger fault. General use original ink cartridges can be restored after repeated washing, but this is way too wasted ink. The easiest way is to use your hands to the head of empty cartridge cleaning. Before cleaning with an empty cartridge, first using a needle as the cartridge out of the residual ink, the cleaner the better, then add the cleaning solution (available aftermarket). Filling cleaning fluid should be carried out in a clean environment, will add a good cleaning fluid cartridge according to the normal operation of the Acer Aspire 1410 Battery printer on the machine, and constantly cleaning the printer button at its cleaning. Use of the residual ink cartridge cleaning fluid mixed with light colors for printing the test, then put on a good cartridge for normal use.
Troubleshooting four: Clean the pump nozzle in the printer troubleshooting
Something is wrong with the printer is more wash pump nozzle, and it is one of the main factors causing plug. Cleaning the printer on the printer nozzle pump nozzle protection plays a decisive role. After the car back to the bit nozzles to clean the pump nozzle from the nozzle to the weak pumping of treatment on the nozzle seal protection. Install a new cartridge in the printer or the nozzles are disconnected, the machine’s suction pump to the bottom nozzle for exhaust through it, the higher the precision of this work mouths as possible. However, in actual use, its performance and air tightness due to time, the dust and ink residues in the mouth of the coagulum increases. If the user is not on its regular inspection or cleaning, it will keep your print head out of some failure.
Conservation of this part of the method: Remove the printer’s top cover away car, using a needle wash them inhaling pure water, in particular, embedded within the pores of the mouth to fully clean the gasket. In this wish to remind users to clean the parts, do not use CANON BP-511 Battery ethanol or methanol to clean them, this will cause this component dissolved in the mosaic of the porous gasket deformation. The other thing to mention is that inkjet printers should be kept away from the heat and dust of the work environment, only a good working environment to ensure long-term regular use of the machine.
Troubleshooting V: Detection of normal and printing ink line processing accuracy was worse
Inkjet printer in use due to use of the frequency and accuracy of time and print gradually worse. Inkjet print head is also a life. General use from the beginning of a new nozzle to the end of life, could not see any fault if more smoothly, that is, the amount of cartridge life of 20-40 months. If your printer has been in use for a long time, and now the printing precision variation, you can use the method of replacement cartridges to try, if for a few cartridges, print output results are the same, then you will this printer’s nozzle to be replaced the. If there is a change after the replacement ink cartridges, HP pavilion dv8000 battery ink cartridges that you may have used poor quality non-original ink.
If the printer is new, the printed results can not satisfy you, often the print line is not clear, text skew graphics, text, graphics outside the boundaries blurred, print out the ink control synchronization accuracy, which means you can buy ink cartridges or false non-original products used cartridges should be its immediate replacement.
Troubleshooting six: walking handling car meet dislocation
Inkjet printers are walking the track the car by two sets of powder alloy of copper with a round shaft to slide with complete precision. While walking there is a small car designed and installed to supplement the shaft lubricating oil Felt, but the environment we live in the dust everywhere, a long time, due to air oxidation, dust the surface of the axis of oil ** Aging The failure, then if it continues to use the printer, will be due to copper sleeve axis and the increased friction caused by car travel dislocation, can not be used until the collision caused the front.
The solution is: Once this failure should immediately turn off the printer, did not return to place his hands back into the car parking spaces. To find a small piece of sponge or felt, full of oil dipped on the sewing OLYMPUS li-40b battery machine oil, tweezers grip rub back and forth on the spindle. It is best to remove the spindle, the cleaned oil, so the best.
Another car is because the device is damaged due to meet. Car parking spaces above the printer have a photoelectric sensor, which is available to print to the printer board reset signal the importance of car components. If this component is too large or damaged due to dust, the printer can not find the car back to the signal due to hit the front, which led to not use the general out of the failure to replace the vgp-bsp13/s Battery device.
